Vigo VG0903K User Manual download pdf (Page 5)

ASSEMBLY

PACKAGE CONTENTS

7. Select the mirror location and mark

holes on the wall for mounting screw.

Measure from the center holes on the

back of the mirror. Measurement should

be the distance between the mounting

holes. Drill holes, sink anchors and secure

screws. Hang up the mirror cabinet and

install screw covers.

6. For specific Faucet installation instructions refer to the Faucet manufacturer's

instruction guide. Connect supply line to faucet.

4. Silicone the lavatories to the countertop, align it and press down firmly.

Note: It could be up to 3/8 inch gap in front of the lavatory between front of the

vanity and lavatory. Install the drain assembly. Connect tailpiece to the drain.

1. Once the product has been unpacked your first step will be to assemble the

unit. Select the vanity location and measure distance between hanging units.

Mark holes on the wall for the wall brackets. Remove brackets, drill holes, sink

anchors and screw the brackets to the wall. This should be drilled into your 2"x6"

backing material.

Holes for the mounting screws

3. Loosen both

adjusting screws in

the vanity hanging

unit. Hang up the

vanity to the wall

brackets. Tighten

adjusting screws.

Side wall of the vanity

Vanity bracket

Wall

Hanging unit

Adjusting screw

Hook



VANITY

MIRROR

PLASTIC ANCHOR

- 4PC.

SCREW -

4PC.

PLASTIC ANCHOR

- 6PC.

SCREW -

6PC.

VANITY

BRACKETS

-2PC.

Wall

Plastic anchor

Screw

5. Connect Trap to drain assembly. Vigo recommends installing the Vigo brand

corresponding sink and pop up. Figure #5 depicts the complete assembly of the

Vigo brand sink, vanity and pop up.

CARE AND MAINTENANCE

REQUIRED TOOLS

SAFETY TIPS

INSTALLATION

Installation must be done by a qualified licensed plumber.

Prior to installation please read the instructions thoroughly, confirm that all parts

are included and visually inspect the unit for any defects.

If you have any questions please contact the Vigo Technical Support

Department before proceeding with installation.

REMOVING YOUR OLD LAVATORY

Adjustable wrench

Plumber's putty or Caulking

Pipe tape

Flat screwdriver

Philips Screw Driver

To ensure that your installation project goes smoothly, please review these

instructions before proceeding.

Your new lavatory is designed for years of trouble-free performance.

Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive

cleaners, steel wool and harsh chemicals.

To protect against scratches, use felt, leather, or cork under all items placed on

the wood surface. Do not expose wood furniture to direct sunlight, drying heat

sources, or dampness. Dust frequently with a soft cloth in the direction of the

grain. Use only products specifically made for cleaning wood. Avoid using oily

polishes or waxes, or products containing silicone. Blot spills immediately with

a soft, damp cloth.

Turn off the water supply. This is done by closing the two shut-off valves

located under the lavatory.

If there are no shut-off valves leading to the lavatory, you must turn off the

water at the main valve. This is usually located in the basement, garage or near

the foundation on the outside of the house. It may also be near the water meter.

Check to be sure the water is off by turning on the faucet where you are

working until the water stops flowing.

If you have shut off the main valve in a two-story house or greater, you should

open the kitchen faucet and another faucet on the same level. Water will then

drain from the entire line. This will help avoid spills. Be sure and close the

faucets before you turn on the main valve again. Disconnect the drain pipes.

Take off as many sections as possible between the lavatory and the wall or

floor to facilitate removal. Place a basin under the work area to catch any water

that may still be in the drain.

Drill

Tape Measure

Tubing Cutter or Hacksaw

Caulking gun

Observe all local plumbing and building codes.

Risk of personal injury or product damage will occur if not handled in the proper

manner. Always consult your licensed contact with any questions or concerns.

Handle with care. Vitreous china/Glass/Acrylic can break or chip if the product is

handled carelessly.

Prior to installation, unpack the new vanity components and inspect it for

damage. Return the material to its protective carton until you are ready to install

it. Inspect the drain and supply plumbing. Replace if necessary.

2. For ease of installation it is recommended for you to install the faucet on the

sink/top at this point. If you are unable to do so at this point and have to install

the faucet at the completion of the vanity see page 6 as this is the needed drawer

removal steps for access for completion of installation. Also, it is recommended

to cut support legs at the same dimension you have picked for the vanity to be off

the floor for extra support while installing.

NOT PROVIDED

TAIL PIECE

DRAIN NUT

TO DRAIN

WASHER

DRAIN ASSEMBLY

SOFT WHITE WASHER

POP UP TOP

INTERNAL BRASS PIECE (POP UP MECHANISM)

DO NOT OVER TIGHTEN THE DRAIN

POP UP DRAIN

RUBBER WASHER

SINK

OVERFLOW

(with overflow)

TAIL PIECE

DRAIN NUT

SOFT WHITE WASHER

TAIL PIECE NUT

WHITE PLASTIC WASHER

POP UP DRAIN TOP

RUBBER WASHER

SINK

INTERNAL BRASS PIECE

(POP UP MECHANISM)

OVERFLOW

WHITE PLASTIC WASHER

1 2 3 4 5 6 7

Comments to this Manuals

No comments

Vigo VG0903K User Manual Page 5

Comments to this Manuals

Related products and manuals for For Home Vigo VG0903K